Forgotten Porsche Projects - Part 3

Behind the scenes at the Weissach development center, there are no taboos. In the first two parts of our series on forgotten projects, we covered road-going prototypes and unrealized racing projects. In this third installment, we will focus on experimental powertrains, alternative engines, and hybrid systems that were often decades ahead of their time.

zapomenute-projekty-porsche-3-01.jpg (800x600) - 164 KB

Experiments of the 60s and 70s: Wankel Rotary Engines

One of the lesser-known projects was the development of Wankel rotary engines. In collaboration with NSU, Porsche worked on both two-rotor and multi-rotor engines, which were tested in experimental versions of the 914 model (sometimes referred to as the 914/28). The prototypes used an engine taken from the NSU Ro80, but Porsche sought to develop its own rotor seals so the engine could withstand the greater stresses of a sports car.

zapomenute-projekty-porsche-3-02.jpg (598x798) - 134 KB

The two-rotor unit produced between 155 and 180 horsepower and was characterized by a compact design, low vibration, and a willingness to rev high. However, testing revealed high fuel consumption and sensitivity in the rotor seals, which proved to be a critical problem during a time of tightening emission regulations and following the 1973 oil crisis. Nevertheless, the experience gained with the Wankel contributed to a deeper understanding of high-revving engine characteristics.

zapomenute-projekty-porsche-3-03.jpg (800x600) - 76 KB

The 16-cylinder 917: A Forgotten Extreme

At the same time Porsche was experimenting with rotary engines, an even more radical project was underway in Weissach. At the turn of 1970 and 1971, as Porsche looked for a way to defeat the dominant McLaren M8Fs in the North American Can-Am series, one of the boldest experiments in the brand's history was created under the leadership of Ferdinand Piëch. This was the 917 test prototype equipped with a flat-16 engine developed by Hans Mezger, sometimes referred to as the Type 912 Flat-16. Structurally, it was an extension of the standard 12-cylinder engine from the 917. Porsche tested various versions with displacements ranging from 6.0 to 7.2 liters. The power output of the largest version pushed toward the 880-horsepower mark.

zapomenute-projekty-porsche-3-04.jpg (800x600) - 116 KB

The theoretical power potential was impressive, but practical tests revealed a fundamental problem – the weight and length of the engine negatively affected weight distribution and the car's handling. The car's behavior was less predictable than the 12-cylinder version, and the benefit of the higher power was not sufficient given the complications the design introduced. The project was therefore halted before it ever saw racing action.

zapomenute-projekty-porsche-3-05.jpg (1053x792) - 447 KB

Instead of further increasing displacement and the number of cylinders, Porsche ultimately decided on a completely different path. It entered the 1972 season with the 917/10 version, equipped with the very first turbocharged 12-cylinder engine featuring a pair of turbochargers. The turbocharged engine offered significantly higher power potential with better weight control and paved the way for the extreme performance that would later exceed the 1,000-horsepower mark in the 917/30 model. The extreme 16-cylinder thus became a victim of the dawn of the turbo era.

Although the 917/16 project remained a dead end, it was also an important milestone. It showed that the way forward was not through increasing the number of cylinders, but through turbocharging, which became one of the key elements of both racing and road cars in the following decades. This experiment demonstrates the brand's technical courage, as Porsche was simultaneously exploring both rotary engines and extreme multi-cylinder units.

zapomenute-projekty-porsche-3-06.jpg (480x640) - 152 KB

Electric and Hybrid Powertrains Long Before the Taycan

The idea of alternative propulsion goes much deeper into history. As early as 1900, Ferdinand Porsche introduced the Lohner-Porsche car with electric motors located directly in the wheel hubs, each producing approximately 2.5 kW. A later version combined an internal combustion engine serving as an electric generator, creating one of the first functional hybrid cars in the world.

zapomenute-projekty-porsche-3-07.jpg (800x600) - 127 KB

The modern hybrid chapter began in earnest in 2010 with the 911 GT3 R Hybrid project. This experimental race car was based on the 997 generation and was equipped with a 4.0-liter flat-six engine producing approximately 480 horsepower, supplemented by two electric motors on the front axle, each providing around 60 kW. Energy was stored by a flywheel system, which allowed for a short-term power boost during acceleration. The car, weighing approximately 1,350 kilograms, debuted at the 2010 24 Hours of Nürburgring and served primarily as a test tool for future hybrid programs. The experience gained was then reflected in the development of the 918 Spyder introduced in 2013 and later in the hybrid versions of the Panamera and Cayenne.

zapomenute-projekty-porsche-3-10.jpg (800x600) - 113 KB

The development of electromobility also reaches deep into the brand's history, but in the modern era, it was more concretely realized with the 2011 Boxster E project. It was a fully electric prototype developed as a mobile laboratory for testing electric vehicle technologies, and a total of three cars were built. The all-wheel-drive version with two motors had 245 horsepower and 540 Nm of torque, while the weaker single-motor version powered the rear wheels with 122 horsepower. The LiFePO battery had a capacity of 29 kWh, a range of about 170 km, and weighed 341 kg out of the car's total 1,600 kg.

zapomenute-projekty-porsche-3-11.jpg (800x600) - 105 KB

The prototype lacked a clutch pedal and gear lever; the tachometer was replaced by an E-Power meter, and the driver could control energy recuperation using buttons on the steering wheel. Due to its quiet operation, Porsche used an Active Sound Design system, producing artificial sound for safety reasons. The Boxster E was not intended for mass production, but its technologies later became a key foundation for the hybrid 918 Spyder and the fully electric Taycan.

zapomenute-projekty-porsche-3-08.jpg (800x600) - 134 KB

Materials of the Future: From Aluminum to Carbon

In addition to experimenting with various powertrain systems, Porsche was intensively involved in the development of construction materials. The 956 race car introduced in 1982 used an aluminum monocoque and a 2.65-liter turbocharged flat-six engine with around 620 to 640 horsepower, with the car's weight hovering around 800 kg. Even then, experiments were being conducted with composite elements, although a full carbon structure was technologically and economically difficult to realize at the time.

zapomenute-projekty-porsche-3-09.jpg (600x450) - 96 KB

The breakthrough came two decades later with the Carrera GT, produced between 2003 and 2006. The car used a carbon monocoque and a 5.7-liter V10 engine with 612 horsepower. The engine was originally created for the canceled LMP2000 racing project with the internal designation 9R3, which we mentioned in the previous article. After the project was terminated, the engine was adapted for road use, creating one of the most technically advanced supercars of its time. The Carrera GT was the first production car in the world with both a monocoque and engine frame made of carbon fiber reinforced plastic (CFRP).

Conclusion

Porsche's experimental projects are not just dead ends, but a systematic building of technical know-how. From rotary engines to the 16-cylinder 917 extreme, hybrid racing projects, and carbon monocoques, the path was full of bold decisions and technical risks. It is precisely these seemingly peripheral projects that enabled the creation of the iconic models that define the brand today.

In the next installment, we will look at canceled Porsche projects, some of which were not just technical experiments but were nearly ready for mass production.

Forgotten Porsche Projects - Part 1 Forgotten Porsche Projects - Part 2 Hybrids and Electric Cars - Porsche Between Tradition and Innovation Will the Porsche 911 Ever Be Purely Electric?


Share:
Share on Facebook Share on Twitter Share on LinkedIn Share via WhatsApp

Did you like the article?
👎 Dislike 0
Steve
6.5. 2026

← Back to History

Discussion (0)

Add a comment



 (Commenting rules)